Drying column chemical tower important internal wire mesh demister
Wire Mesh Demister Mist Eliminators Standard Specification
1.General introduction of wire mesh demister
Demister pads or Mist eliminators are porous blankets of metal or
plastic knitted wire mesh, designed and constructed for the
efficient, economical removal of entrained liquid droplets from
vapor streams. Demister Pads can be fabricated in any required size
and shape and may be installed in new or existing process vessels.
2. How Wire Mesh Demister Works?
When vapor and entrained liquid droplets pass through a mist
eliminator, the vapor moves freely through the mesh pad but the
liquid droplets, due to their greater inertia, cannot make the
necessary sharp turns and as a result are thrown into contact with
the wire surfaces and briefly held there. As more droplets enter
the pad and collect on the wires, they grow in size, run down the
wire to the bottom surface of the mesh separator and fall from the
unit. Overhead vapor is now free of entrained liquid.
3.Wire Mesh Materials
3.1Metallic Mesh Pads
Materials for metallic Mist Eliminators are as per customer need.
Type 304 or Type 316 mesh pads can be in accordance with ASTM
A-478. Monel mesh pads can be in accordance with ASTM B-164.
3.2Non-metallic Mist Eliminators
Non-metallic Mist Eliminators shall be PTFE or polypropylene as
specified in by customer.
3.3Supports
A.Supports welded to the vessel shall be the same material as the
shell. Where the shell is lined, supports welded to the lining
shall be the same material as the lining.
B.Supports not welded to the shell (e.g. beams) shall be the same
material as the Mist Eliminator.
3.4Grids
A.Metallic grids can be the same material as the mesh pad
B.For non-metallic mesh pads, the grids shall be carbon steel,
coated with the same material as the mesh pad.
3.5Fastening Devices
A.For metallic mesh pads the wire ties or other fastening devices
shall be of the same material as the Mist Eliminator.For
non-metallic mesh pads, the grids shall be carbon steel, coated
with the same material as the mesh pad.
B.For non-metallic mesh pads the wire ties can be the same material
as the mesh pad.
4. Demister Inquiry Table if Calculation Suggestions and Service are
needed
| Please State your demister / mist eliminator application |
|
| Operating data |
| Gas | Max. gas volume flow (operating conditions) | M3/h | |
| Gas density (operating condistions) | Kg/m3 | |
| Operating pressure | Bar (a) | |
| Operating temperature | ℃ | |
| Liquid | Liquid content | Kg/h | |
| Liquid density | Kg/m3 | |
| Dynamic viscosity of the liquid | mPas | |
| Geometrical data |
| Flow direction | Horizontal | ¨ |
| Vertical | ¨ |
| Installed in | Column | ¨ |
| Pipe | ¨ |
| Column diameter or dimensions | mm | |
| Opening for installation | Manhole | ¨ DN |
| Vessel flange | ¨ Size |
| Requirements |
| type of mist eliminator | Wire mesh demister | |
| Material | | |
| Efficiency of separation | % | |
| Max. pressure drop | | |
| Miscellaneous | | |
Please pay attention to the Unit when refering to this sheet.
5. What can factory do for you in the wire mesh demister?
1. demister is tailor made to suit for specific vessel dimensions
and configuration.
2. provides wide variety of material to suit for even the most
corrosive process environments.
3. factory can supplies either mesh pad only, or complete demister
with top and bottom supporting grids for direct installation in
vessels.
4. Sectional construction for easy handling and access through man
ways.
5. Complete accessory pack including support ring and beam can be
provided when required.
Wire Mesh Demister workshop:
